Buffer Stops
Easy to assemble laser-cut kit to make 2 buffer stops in less than 10 minutes. Pre-wired LEDs can be powered by 12-16 V DC or AC power supply. Fits to all HO/OO tracks with or without ballast.
€13.50Price
Subcategory
159 products
Grid
Grid-2
List
List-2
Catelog
Active filters
Buffer Stops
Easy to assemble laser-cut kit to make 2 buffer stops in less than 10 minutes. Pre-wired LEDs can be powered by 12-16 V DC or AC power supply. Fits to all HO/OO tracks with or without ballast.
€13.50Price
Buffer Stops
Fits to HO/OO scale tracks without ballast such as Atlas, Hornby,...
€13.50Price
€95.00Price
Ballasting Solutions
Pack includes below tools.
Ballast Spreader
Parallel Track Tools
Flexible Track Tool
Track Voltage Tester
Snap & Glue Magnetic Clamps
€95.00Price
Tools For Modelers
A set of paired magnetic set squares.
Simply pull apart, place inside and outside your 90 degree corner and snap into place.
The snap and glue set squares hold the two pieces of plastic in place and allow you to glue them at the right angle without further worry.
After curing of the adhesive do remove easily the Snap...
€37.00Price
€15.00Price
Ballasting Solutions
Perfect ballast spreading is never problem again with this easy to use Ballast Spreader.
Slots underneath the spreader keeps your ballast in line, spreads the ballast on track and never on rails.
€15.00Price
€55.00Price
Cradles, Testers, Rollers
Specifications:
Board Size: 220 X 163 mm
Blades: 17-19 mm scored (snap-off, break-off) standard cutter blades.
Cutting height: Up to 8 mm depending on the width and hardness of timber or profile.
Cutting width: Up to 30 mm depending of the height and hardness of timber or profile.
Materials to cut: Soft woods, styrene,...
€55.00Price
€99.00Price
Cradles, Testers, Rollers
Specifications:
Overall size: 225 X 165 X 65m
Power adapter input voltage: 100/240 V
Power adapter output voltage: 18-20V DC, 3A
Cutting disk size: 38mm
Cutting height: 5mm
Materials to cut: Model train tracks, non-ferrous soft metals.
<p...
€99.00Price
€21.00Price
Track Laying Tools
Flexible track is very useful but its tendency to straighten up makes track laying difficult unless it can be held in position. This new Flexible Track Holding Tool keeps your flexible track in the desired curve temporarily before fixing it permanently. You can even hold the track in your hands, off the baseboard, without it losing its curves! Suitable for all TT scale tracks. Can be used...
€21.00Price
€20.00Price
Track Laying Tools
For all TT scale tracks. One set includes 2 Tools. This very useful track alignment tool is designed to keep the same distance between the centers of adjacent and parallel tracks. You can adjust the distance between the mids of tracks from 30 mm to 90 mm or from 1.2 inch to 3.5 inches. With Parallel Track Tool you can lay your straight and curved tracks in perfect parallel with ease.
€20.00Price
€13.50Price
Buffer Stops
Fits to HO/OO scale tracks without ballast such as Atlas, Hornby, Peco, Lima, etc.
Nickel silver track with a fishplate underneath the buffer stop is directly wired to LED light.
€13.50Price
€13.50Price
€13.50Price
Buffer Stops
Fits to HO/OO scale tracks without ballast such as Atlas, Hornby,...
€13.50Price
€13.50Price
Buffer Stops
Fits to HO/OO scale tracks without ballast such as Atlas, Hornby,...
€13.50Price
€15.00Price
Perfect ballast spreading is never problem again with this easy to use Ballast Spreader.
Slots underneath the spreader keeps your ballast in line, spreads the ballast on track and never on rails.
€15.00Price