Check not just if your track has power - but also how much! <br...

Our classic ballast spreader with a shut off mechanism added.

2 paires of right angle magnetic clamps and 2 pairs of magnetic clamps with adjustable angles. Simply pull apart, place inside and outside your corners and snap into place. The snap and glue pairs hold the two pieces of plastic, wood, etc. in place and allow you to glue them at the desired angle without further worry. <p...

Perfect ballast spreading is never problem again with this easy to use Ballast Spreader. Slots underneath the spreader keeps your ballast in line,  spreads the ballast on track and never on rails.

A set of paired magnetic set squares. Simply pull apart, place inside and outside your 90 degree corner and snap into place. The snap and glue set squares hold the two pieces of plastic in place and allow you to glue them at the right angle without further worry. After curing of the adhesive do remove easily the Snap...

For all HO and OO tracks. One set includes 2 Tools. This very useful track alignment tool is designed to keep the same distance between the centers of adjacent and parallel tracks. You can adjust the distance between the mids of tracks from 30 mm to 90 mm or from 1.2 inch to 3.5 inches. With Parallel Track Tool you can lay your straight and curved tracks in perfect parallel with ease.

Specifications: Board Size: 220 X 163 mm Blades: 17-19 mm scored (snap-off, break-off) standard cutter blades. Cutting height: Up to 8 mm depending on the width and hardness of timber or profile. Cutting width: Up to 30 mm depending of the height and hardness of timber or profile. Materials to cut: Soft woods, styrene,...

Adjustable height setting allows you to alter the depth of ballast  and cope with different Code Rail.   Shut off valve - now you can halt the flow of ballast whilst you lift the Ballast Spreader over point work or when it reaches the end of the track.   Loco hauled - You can now pull the Ballast Spreader with a locomotive as well as by hand.

Perfect ballast spreading is never problem again with this easy to use Ballast Spreader. Slots underneath the spreader keeps your ballast in line,  spreads the ballast on track and never on rails.

Proses hold and glue right angle holders for kit buildings and modellers. Pack contains 2 holders, simply pull apart, place inside and outside your 90 degree corner and fix the wing nuts.

Voltage tester for Slot tracks, both at 1:43, 1:32 and 1:24 scale. This Proses tester, based on those used by the brand in its range of railways models accessories, not only allows to check if there is voltage on the track if not how much. Led indicators light up for 5 to 9V, 9 to 12V and +12V. It's design allows the use in most marketed...

A set of paired magnetic clamps with adjustable angles. Simply pull apart, place inside and outside your corners and snap into place. The snap and glue set squares hold the two pieces of plastic in place and allow you to glue them at the desired angle without further worry. After curing of the adhesive do remove easily...

Specifications: Overall size: 225 X 165 X 65m Power adapter input voltage: 100/240 V Power adapter output voltage: 18-20V DC, 3A Cutting disk size: 38mm Cutting height: 5mm Materials to cut: Model train tracks, non-ferrous soft metals. <p...

A set of paired magnetic set squares. Simply pull apart, place inside and outside your 90 degree corner and snap into place. The snap and glue set squares hold the two pieces of plastic in place and allow you to glue them at the right angle without further worry. After curing of the adhesive do remove easily the Snap...

Tire truer and cleaner for 1:32 and 1:24 scale slot cars. Coarse and fine sandpapers and spare cleaning felts are included. The unit picks power from your own track thus you can control the turning speed of the tires with your own hand controller whether it’s an analog or a digital car. <span...

Check not just if your track has power - but also how much! <br...

Another great tool to end your challenges to get your long, multi wheel locos on tracks with ease. The aluminum base is powered by the track it is placed on and lets the loco run and get on the track smoothly and properly. Both ends are open to giving access to both sides of the track. Base length: 48 cm Scale: HO/OO <table cellpadding="0" cellspacing="0"...

Flexible track is very useful but its tendency to straighten up makes track laying difficult unless it can be held in position.  This new Flexible Track Holding Tool keeps your flexible track in the desired curve temporarily before fixing it permanently.  You can even hold the track in your hands, off the baseboard, without it losing its curves!  Suitable for Peco, Hornby, Jouef, Mehano,...

Ballast Spreader and Gluer combo. Perfect ballast spreading is never problem again with this easy to use Ballast Spreader. Slots underneath the spreader keeps your ballast in line,  spreads the ballast on track and never on rails. Ballast Gluer is another innovative tool from Proses workshops to glue track ballast with ease and quickly.

Advanced Ballast Spreader Car and Ballast Glue Applicator Set. Adjustable height setting allows you to alter the depth of ballast and cope with different Code Rail.   Shut off valve - now you can halt the flow of ballast whilst you lift the Ballast Spreader over point work or when it reaches the end of the track.   Loco hauled - You can now pull the Ballast Spreader with...

For all N scale tracks. One set includes 2 Tools. This very useful track alignment tool is designed to keep the same distance between the centers of adjacent and parallel tracks. You can adjust the distance between the mids of tracks from 30 mm to 90 mm or from 1.2 inch to 3.5 inches. With Parallel Track Tool you can lay your straight and curved tracks in perfect parallel with ease.

Ballast Gluer is another innovative tool from Proses workshops to glue track ballast with ease and quickly..

Spares for TC-501 and TC-501 Tire Truer and Cleaner for 1:32 and 1:24 scale slot cars. Coarse and fine sandpapers and spare cleaning felts. (3 of each)

Parallel Track Tool (67mm) is designed to keep the same distance between the centres of adjacent and parallel tracks of Hornby, Peco, Branchline and most UK geometry tracks. With Parallel Track Tool you can lay your straight and curved tracks (first, second, third and fourth radius) in perfect parallel very easily. One set includes 4 tools.